Home Page
   Articles
       links
About Us    
Traders        
Recipes            
Latest Articles
120 degree bracket
Page 1, 2  Next
 
Post new topic   Reply to topic    Downsizer Forum Index -> Make Your Own/DIY
Author 
 Message
jema
Downsizer Moderator


Joined: 28 Oct 2004
Posts: 28237
Location: escaped from Swindon
PostPosted: Sun May 15, 16 4:48 pm    Post subject: 120 degree bracket Reply with quote
    

My search abilities are getting beaten here. I want to create a 3m diameter hexagonal mould to pour cements into.
Some 120 degree brackets would make life simple. I can find images and can import them by the million from alibaba, but 6 would be a better option.

 
Nick



Joined: 02 Nov 2004
Posts: 34535
Location: Hereford
PostPosted: Sun May 15, 16 6:15 pm    Post subject: Reply with quote
    

Make a wooden former?

Eta. Are you after metal brackets to do exactly this? Doh.

 
Nick



Joined: 02 Nov 2004
Posts: 34535
Location: Hereford
PostPosted: Sun May 15, 16 6:55 pm    Post subject: Reply with quote
    

https://www.ebay.co.uk/itm/271746822626

 
jema
Downsizer Moderator


Joined: 28 Oct 2004
Posts: 28237
Location: escaped from Swindon
PostPosted: Sun May 15, 16 7:43 pm    Post subject: Reply with quote
    

Looks very small, and seriously all the way from the USA for something that can't be that esoteric?
Glad to see it isn't easy to find though, thought I was going daft.

 
onemanband



Joined: 26 Dec 2010
Posts: 1473
Location: NCA90
PostPosted: Sun May 15, 16 9:04 pm    Post subject: Reply with quote
    

Make from plywood.
Screw 2x2 (or whatevers handy) along ply edge to enable fixing to your mould.

 
jema
Downsizer Moderator


Joined: 28 Oct 2004
Posts: 28237
Location: escaped from Swindon
PostPosted: Sun May 15, 16 9:18 pm    Post subject: Reply with quote
    

a diy approach is clearly possible, but a lot more work and chance to be a bit off on degrees.

 
vegplot



Joined: 19 Apr 2007
Posts: 21301
Location: Bethesda, Gwynedd
PostPosted: Sun May 15, 16 9:46 pm    Post subject: Reply with quote
    

As the radius of a circle is the edge length of a hexagon it's easy enough to draw a hexagon on the ground using cord and marker tool. You can then mark the intersections with marker spray and construction your mould using these marks as guides.

 
Nick



Joined: 02 Nov 2004
Posts: 34535
Location: Hereford
PostPosted: Sun May 15, 16 10:10 pm    Post subject: Reply with quote
    

jema wrote:
Looks very small, and seriously all the way from the USA for something that can't be that esoteric?
Glad to see it isn't easy to find though, thought I was going daft.


Well. I googled 120 degree bracket and it popped up. Do you know anyone in IT who could help you?

 
onemanband



Joined: 26 Dec 2010
Posts: 1473
Location: NCA90
PostPosted: Mon May 16, 16 8:16 am    Post subject: Reply with quote
    

jema wrote:
.......... a lot more work and chance to be a bit off on degrees.


Nah.
4 foot square piece of ply, in the middle draw your hexagon with 1 foot sides, screw 2x2 to ply thus forming a hexagon of 2x2, number-up 2x2 and remove, cut out middle of ply (erring on large side as re-fitted 2x2 will still be at 120"), re-fit 2x2, cut whole thing into 6, voila 6 6inch long brackets.

 
onemanband



Joined: 26 Dec 2010
Posts: 1473
Location: NCA90
PostPosted: Mon May 16, 16 8:48 am    Post subject: Reply with quote
    

OTOH if I was going about it I wouldn't make brackets.
I would make a hexagon from 8 foot lengths of 4x1 laid flat (overlapping each other). Leave excess length at corners so they can be braced. That could give an accurate hexagon and brace the mould nicely.

 
dpack



Joined: 02 Jul 2005
Posts: 46233
Location: yes
PostPosted: Mon May 16, 16 9:54 am    Post subject: Reply with quote
    

onemanband wrote:
OTOH if I was going about it I wouldn't make brackets.
I would make a hexagon from 8 foot lengths of 4x1 laid flat (overlapping each other). Leave excess length at corners so they can be braced. That could give an accurate hexagon and brace the mould nicely.


this

use a biggish 120 cornered bit of ply to set each corner of the mould and a short bit of wood screwed onto the top edges to create a triangle brace before fixing the end and lower edge by direct screws into the adjacent length.

this requires one end of the 4 x 1 to be cut at a perfect 90 degrees and a flat surface to work on (or use a spirit level and shims if you are constructing on a wonky surface in situ and need a flat level top to the concrete)

fixing the middle of each length with either a peg to the floor or by cross bracing to a bit of ply in the middle will keep the outside edges from bowing out when pouring.cross bracing makes it more difficult to use a plank to sweep the surface flush with the top of the mould so pegs are better.

remember to vibrate (or cut with a shovel) the concrete to remove air bubbles and compact the solids.don�t over do it or use a very wet mix as the lumps will all settle leaving only sand and water at the surface.

in something that size reinforcing mesh will help to prevent cracking .

there are many compositions of concrete but for a wide ,relatively thin slab i would probably go for

2 mixed aggregate,2 sharp sand,1 portland,1 lime

for a pale(or tinted colour ) i would use 1" to dust granite and snowcem /lime in a 4:1:1 mix

 
onemanband



Joined: 26 Dec 2010
Posts: 1473
Location: NCA90
PostPosted: Mon May 16, 16 1:32 pm    Post subject: Reply with quote
    

Dpack, you're not wrong, but I think you slightly misunderstood my plan or missed the words "laid flat"
8 foot 4 X 1's laid flat on floor, alternately overlapping. Easy to set up as hexagon with a tape and a square. Once set up as hexagon whack in 2 screws at each corner, then add further braces across oversailing timber, thus triangularly bracing it.

You will need to make at least 2 of these. One for top, one for bottom. Fix mould faces to inside of the flat 4 x 1 hexagons.
4 x 1 laid flat will not bow out, so no need for cross-bracing and no obstructions to trowelling.

 
Tavascarow



Joined: 06 Aug 2006
Posts: 8407
Location: South Cornwall
PostPosted: Mon May 16, 16 3:05 pm    Post subject: Reply with quote
    

Cut your mould from reasonably thick timber with a skill saw or bench saw set at 60 degrees & hold it together with a ratchet strap.
When the cements cured loosen the strap & remove the mould.
No brackets needed.

 
Tavascarow



Joined: 06 Aug 2006
Posts: 8407
Location: South Cornwall
PostPosted: Mon May 16, 16 3:06 pm    Post subject: Reply with quote
    

Actually I think that should be 30 degrees each end.
You can work it out.

 
jema
Downsizer Moderator


Joined: 28 Oct 2004
Posts: 28237
Location: escaped from Swindon
PostPosted: Mon May 16, 16 6:26 pm    Post subject: Reply with quote
    

thanks folks, I will have a play.

 
Post new topic   Reply to topic    Downsizer Forum Index -> Make Your Own/DIY All times are GMT
Page 1, 2  Next
Page 1 of 2
View Latest Posts View Latest Posts

 

Archive
Powered by php-BB © 2001, 2005 php-BB Group
Style by marsjupiter.com, released under GNU (GNU/GPL) license.
Copyright � 2004 marsjupiter.com